CRL 950FC Series Fast Cure High Viscosity Urethane Adhesive

Home > Exterior > Auto Glass > Adhesives , Sealants, Cleaners > Adhesives >

CRL 950FC Series Fast Cure High Viscosity Urethane Adhesive - 10.5 Fl. Oz

Retail Price: $14.99
You Pay!: $12.49
You save $2.50!

Availability:: Usually Ships in 24 to 72 Hours
Part #: CRL950FC

Qty:

Description

CRL950FC Fast Cure Urethane Adhesive is a fast curing adhesive that passes or exceeds U.S. Federal Motor Vehicle Safety Standards FMVSS212 (Barrier Crash Test) and FMVSS208 (Occupant Crash Protection) in its most severe interpretation with dual air bags and unrestrained dummies. Quick curing and high viscosity are features you normally find in higher priced urethanes, but CRL offers these same features in our value priced CRL950FC. Guns smoothly, is non-sagging, provides a sure bond, and rates non-conductive. The fast curing formula is tack free in only 20 to 30 minutes and offers Safe Drive Away Time in as little as 45 minutes when used on vehicles without a passenger side air bag, four hours with passenger air bag at 73°F (23°C) and 45% RH (relative humidity).

New packaging for improved shelf life features a spread metal plunger that replaces the plastic plungers. This provides worry-free cartridges that are always easy to gun. In addition, the extra and difficult step usually required to remove the sharp bottom metal seals is gone, and with the new spread metal plunger there is no need for a desiccant capsule to help keep the urethane fresh.

In addition, as an added value, each cartridge has a peel-off Quality Control Label affixed to the bottom of the tube. The Quality Control Label contains the following information: Cat. No. of the Urethane Adhesive used; Batch # of cartridge used; Date of Use; Temperature; Humidity; Airbag? Yes or No; and Safe Drive Away Time. After this label has been filled out completely by the technician installing the windshield, it can then be affixed to your customer's invoice for insurance purposes or as a quality control record for you and your customer.

Cleaning and Primers
CRL 900 and 700 Series Urethanes are supported by a selection of primers formulated for use in all aspects of glass bonding, including a glass frit primer, a pinchweld primer, and a primer specifically formulated for use with EPDM/PVC moldings.
1. After removing all of the old urethane to within 1/16 inch (1.5 millimeter) of the pinchweld, prepare the pinchweld following the procedures outlined in the CRL Technicians Training Manual. Prime these areas with CRL9P Pinchweld Primer.
2. Clean the inside of the windshield with a lint-free towel 1550 and PWR22 Automotive Glass Cleaner.
3. Apply CRL9GC Glass Primer to frit area with a lint-free towel and wipe dry. Allow to flash off for a minimum of 10 minutes, but no more than 8 hours before installing adhesive. This procedure must be performed above 40°F (4°C). NOTE: CRL9GC Glass Primer must be used prior to any adhesive application to prevent glass displacement. Failure to do so may result in personal injury or property damage.
4. Apply CRL9EP EPDM/PVC Primer to encapsulated moldings if they are part of the bonding area.

For use by trained applicators only. Please refer to C.R. Laurence Technician Training Manual, Technical Spec Data Sheet and Material Safety Data Sheet before using product. CRL9GC Glass Primer must be used prior to any adhesive application to prevent glass displacement. Failure to do so may result in personal injury or property damage. Store cartridges closed and upright when not in use. Store between 65°F (18°C) and 75°F (24°C) in dry conditions.

Meets or Exceeds U.S. Federal Motor Vehicle Safety Standards 208 and 212, and OEM Strength Requirements
Fast Curing Adhesive at a Great Price
Part of the LYNX Services Program

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Exterior > Auto Glass > Adhesives , Sealants, Cleaners > Adhesives
Exterior > Auto Glass > Adhesives , Sealants, Cleaners